Quality management system audit versus product inspection: when each applies: part 4
Approval is a written decision with conditions, not a feeling left over from a good audit day. The factory verdict sets the partnership frame, lot checks govern each release, and conformity routes handle market access on their own terms. Buyers who document all three layers, with triggers for refreshing each, keep sourcing decisions defensible as conditions evolve.
Key takeawaysDocument approvals with scope, conditions, inspection intensity, and re-verification triggers in writing. · Route marking and market-access questions through their designated conformity channels, not through audit scores. · The CE marking framework assigns defined duties that audit evidence supports but never discharges [1]. · Technical regulations sit above factory management in a structure described by the WTO TBT agreement [2]. · Refresh factory evidence on change signals and let lot data trigger re-verification between visits.
This is part 4 of the series on audits versus inspections, focused on decisions. Parts 1 through 3 separated the two tools and their timing; here we address what buyers do with the combined evidence: granting approval, setting conditions, and keeping the file current as conditions change.
Approval decisions go wrong in two familiar ways. Some buyers treat any passing audit as permanent clearance and drop lot checks, while others treat every failed inspection as proof the factory must be replaced. Both reactions ignore what each piece of evidence actually measures.
A steadier approach writes approvals with conditions, routes conformity questions through their proper channels, and refreshes factory evidence on triggers rather than habit. The sections below make that approach concrete.
Writing approvals that age well
A durable approval fits on one page: the audit scope and date behind it, findings closed versus conditionally scheduled, the inspection intensity for upcoming lots, and the trigger or date for re-verification. This note prevents the most common failure, which is a pass remembered broadly while its scope and conditions are forgotten within a quarter.
Conditions should name evidence, not attitudes. Instead of requiring the supplier to strengthen awareness, require the revised instruction at workstations, the calibration certificates for named gauges, or the corrective files with later-production verification. Each condition gets an owner and a date, and approval stays conditional until structural items close. Vague conditions invite later disputes about whether they were met, while named documents with dates make compliance checkable by anyone reviewing the file months afterward.
Buyers formalizing this discipline often standardize on a UTS quality management system audit UTS quality management system audit as the factory-evidence layer, because a consistent report format makes conditions comparable across suppliers. Standard inputs produce comparable approvals, which is exactly what a multi-supplier program needs when buyers rotate between sources.
Conformity routes stay separate
Marking duties belong to product evidence
Market-access marking answers a different question from factory capability, with duties allocated to manufacturers and importers through designated assessment routes. The CE marking framework illustrates the split: it defines what the marking signifies and who bears which obligations [1]. An audit pass never authorizes a marking decision, however tidy the document system behind it.
Technical regulations above the factory layer
Technical regulations and their assessment procedures form a governance layer above factory management, a structure reflected in the WTO agreement on technical barriers to trade [2]. Sourcing budgets for regulated goods should therefore carry two lines: factory verification and product conformity work. Collapsing both into a single audit fee leaves the second job unfunded and undone. Buyers costing regulated programs should therefore confirm that both verification layers appear in the budget, because an audit-only plan leaves product evidence to chance.
Decision matrix
| Evidence situation | Approval stance | Next verification |
|---|---|---|
| Pass with minor notes | Approve with dated housekeeping | Standard lot checks continue |
| Conditional on structural gaps | Conditional approval in writing | Evidence review then normal checks |
| Failed lot from approved factory | Hold releases, not the partnership | Re-inspection plus process review |
| Change in lines or sites | Suspend extension to new work | Focused audit of changed area |
| Recurring lot defects | Escalate to process audit | Tightened checks until closure |
| Regulated market shipment | Separate conformity file required | Applicable assessment route |
Keeping evidence current
- Document the decisionWrite scope, conditions, inspection levels, and re-verification triggers into a one-page approval note signed by the decision owner.
- Watch lot dataTrack lot defect rates and repeat the checks that failed, using the trend as the trigger for process-level review.
- Re-verify on changeOrder a focused visit when lines, sites, staff, or volumes change rather than stretching old verdicts over new conditions.
- File layers separatelyKeep factory, lot, and conformity files side by side so each decision draws on the layer that actually answers its question.
Approvals expire through change faster than through time. A two-year-old pass over unchanged lines with clean lot data outranks a six-month-old pass followed by new sites and drifting defect rates.
Sources
- Wikipedia: CE marking —— Overview of CE marking as conformity marking for products sold in the European Economic Area.
- WTO: Agreement on Technical Barriers to Trade —— WTO portal for the TBT Agreement covering technical regulations, standards and conformity assessment.
Frequently asked questions
How should a supplier approval be documented?
Write the approval with its conditions: scope covered, findings closed or scheduled, inspection intensity for coming lots, and the date or trigger for re-verification. Approvals without conditions age badly because nobody remembers what the verdict covered. A one-page approval note prevents most later disputes. Circulate the note to everyone involved in ordering and receiving, so warehouse staff and quality reviewers apply the same conditions the decision-maker intended.
Does audit approval authorize CE marking?
No. Marking reflects defined manufacturer and importer duties assessed through designated routes, as the CE marking framework sets out. The audit supports consistent production but the marking decision needs product-level evidence through the applicable route. Keep the two files separate and never let one stand in for the other.
Where do technical regulations fit in the comparison?
Treat them as complexity above factory management, governed by the WTO framework for technical barriers to trade. The audit tells you whether the factory can hold a process; conformity assessment tells you whether the product meets the destination market's requirements. Budget for both when costing regulated goods.
How often should factory evidence be refreshed?
Change, not the calendar alone. New product lines, moved or added sites, key staff turnover, significant volume jumps, and recurring lot defects each justify a focused visit. Between visits, lot inspection data serves as the early warning system that triggers re-verification.